ASTM E165

Liquid penetrant examination methods indicate the presence, location and, to a limited extent, the nature and magnitude of the detected discontinuities. Each of the various methods has been designed for specific uses such as critical service items, volume of parts, portability or localized areas of examination. The method selected will depend accordingly on the service requirements.

1. Scope

1.1 This test method covers procedures for penetrant examination of materials. They are nondestructive testing methods for detecting discontinuities that are open to the surface such as cracks, seams, laps, cold shuts, laminations, through leaks, or lack of fusion and are applicable to in-process, final, and maintenance examination. They can be effectively used in the examination of nonporous, metallic materials, both ferrous and nonferrous, and of nonmetallic materials such as glazed or fully densified ceramics, certain nonporous plastics, and glass.

1.2 This test method also provides a reference:

1.2.1 By which a liquid penetrant examination process recommended or required by individual organizations can be reviewed to ascertain its applicability and completeness.

1.2.2 For use in the preparation of process specifications dealing with the liquid penetrant examination of materials and parts. Agreement by the user and the supplier regarding specific techniques is strongly recommended.

1.2.3 For use in the organization of the facilities and personnel concerned with the liquid penetrant examination.

1.3 This test method does not indicate or suggest criteria for evaluation of the indications obtained. It should be pointed out, however, that after indications have been produced, they must be interpreted or classified and then evaluated. For this purpose there must be a separate code or specification or a specific agreement to define the type, size, location, and direction of indications considered acceptable, and those considered unacceptable.

1.4 The values stated in inch-pound units are to be regarded as the standard. SI units are provided for information only.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D1193Specification for Reagent Water
D129 Test Method for Sulfur in Petroleum Products (General Bomb Method)
D1552 Test Method for Sulfur in Petroleum Products (High-Temperature Method)
D4327 Test Method for Anions in Water by Chemically Suppressed Ion Chromatography
D516 Test Method for Sulfate Ion in Water
D808 Test Method for Chlorine in New and Used Petroleum Products (Bomb Method)
E1208 Test Method for Fluorescent Liquid Penetrant Examination Using the Lipophilic Post-Emulsification Process
E1209 Test Method for Fluorescent Liquid Penetrant Examination Using the Water-Washable Process
E1210 Test Method for Fluorescent Liquid Penetrant Examination Using the Hydrophilic Post-Emulsification Process
E1219 Test Method for Fluorescent Liquid Penetrant Examination Using the Solvent-Removable Process
E1220 Test Method for Visible Penetrant Examination Using the Solvent-Removable Process
E1316 Terminology for Nondestructive Examinations
E1418 Test Method for Visible Penetrant Examination Using the Water-Washable Process
E433 Reference Photographs for Liquid Penetrant Inspection
E543 Practice for Evaluating Agencies that Perform Nondestructive Testing
MIL-STD-410 Nondestructive Testing Personnel Qualification and Certification
429 Method for the Examination of Water and Wastewater
ANSI/ASNT CP-189 Standard for Qualification and Certification of Nondestructive Testing Personnel
NAS-410 Certification and Qualification of Nondestructive Test Personnel
Recommended Practice SNT-TC-1A for Nondestructive Testing Personnel Qualification and Certification

Index Terms

fluorescent liquid penetrant testing; hydrophilic emulsification; lipophilic emulsification; liquid penetrant testing; nondestructive testing; solvent removable; visible liquid penetrant testing; water-washable methods; ICS Number Code 19.100

Citing ASTM Standards

[Back to Top]